This is the NEW fully engineered solution that replaces the dust collection attachment on your Bosch Axial Glide Compound Sliding Miter Saw. You will see a HUGE improvement in dust collection efficiency with this upgrade - all without losing your saw's capacity! In the rare cases where this dust chute gets in the way, simply remove it via (2) thumb screws and replace when you're done. This chute is printed in a green/blue (close to Bosch colors) high strength PETG plastic with red accent anodized thumb screws. This item comes with EVERYTHING YOU NEED to install on your saw.NOTE: Each saw model is very different so it's important that you choose the EXACT model of your saw. Please confirm before ordering. This new version has several improvements over the GEN I design: 1. Captured blade slot and reinforced body to prevent small offcuts from breaking your dust chute!2. Increased clearance so you can now cross cut 8/4 boards3. Flexible vacuum hose for even more hose connection options (not for EU model)4. Locking vacuum hose adaptersIncluded:(1) Dust Collection Chute Body(1) Hub Mount that attaches to the saw blade shroud(2) Flexible rubber flaps(1) Flexible Hose Segment (not for EU model)(1) Hose Transition (1.625" OD / 1.4" ID) (not for EU model)(1) Hardware set (2 red anodized thumb screws, 5 philips flap screws)(1) Install Card with QR Code for complete installation videoOptional:(1-2) Vacuum hose adapters (see below) Fitting Name OD ID Works with Hose Transition 1.625" (41.2mm) 1.4" (35.5mm) Small extractor hoses, Festool D27 Medium Adapter 2.00" (50.8mm) 1.75" (44.5mm) Common adapters, Festool D36 Large Adapter 2.45" (62.2mm) 2.25" (57.1mm) Shop Vac, 2.5" Dust Collection Hose If you're in desperate need of some cleanliness in your shop, look no further! This product was meticulously designed and tested to optimize dust collection efficiency while balancing the constraint on the saw. Thank you!

Drastically improve the dust collection on your RIDGID Dual Bevel Miter Saw (with articulating arms) with this 3D Printed dust chute. It requires NO modification of the saw and bolts in the exact same spot as the stock dust chute. NOTE: This solution is designed SPECIFICALLY for the Ridgid models R4251, R4231, and R4241 model numbers. It will also fit the Delta Cruzer models 26-2251 & 26-2241 but there is a separate listing for the Delta version Dust Chute Benefits:- Massive improvement in dust collection with a standard shop vac (~100 CFM airflow)- Can be used in *most* mitered cuts without removal. Due to the saw's small size it cannot be used in full 45 degree bevel cuts...unfortunately- Allows clearance for most common lumber dimensions- Keeps your shop clean(er)!This product includes: (1) Dust Collection Chute Body(2) Flexible rubber flaps(4) Flap Mounting Screws(1) Install Card with QR Code for complete installation video You can also opt for "the works" which also includes a 3D printed dust collection hose adapter (for standard 2-1/2" dust collection hoses), and a wall hose guide.

This listing is for the digital plans for the "Versatile Workbench" as featured on the Shop Nation YouTube channel which is sure to increase your garage shop efficiency! This piece of shop furniture is intended to be used as an out feed table for your table saw, general workbench, and/or assembly table. The design is modular in nature so customizing to fit your exact needs is fairly easy. The workbench measures 72" long by 48" wide by 34.5" tall. The height was chosen so that it would work with most table saws, who have a height of 35". There is a full build series on my YouTube channel (Shop Nation) if you would like to follow along. The first build video is set to release in late January 2021. The approximate cost for building the workbench as designed with all of the bells & whistles is ~$1600 (this will of course vary for everyone) Wood only - $475 Dust Collection System - $380 Electrical System - $75 Hardware - $250 Everything Else - $500 (router lift, T-Track, etc) Tag me on social if you're building this project (@dreamshopnation on Instagram) with the hashtag #shopgreatness. When you purchase these plans you can request the latest revision at any time - for no additional charge! Happy building!!! With purchase of the plans you are entitled to latest version if you ask me! Revision History: Version 1.2 - 1/23/2021 Removed direct product links, replaced with QR Codes, Simplified Appendix Version 1.3 - 1/28/2021 Updated minor discrepancies, fixed vertical support dimension (18.5") on page 34, added build series playlist link, adjusted face frame piece on cut list Version 1.4 - 2/14/2021 Very minor updates, mostly cosmetic Version 1.5 - 3/18/2021 Updated links, changed dust collection door width to 14.3125" and router door lift to 14" to better accommodate 1/2 overlay hinges. Changed drawer F/B width to 27" to ensure better fit with drawer slides. Version 1.6 - 4/15/2021 Minor updates, included spacing for drawer fronts and doors for reference when mounting, made 2x4 cut sheets more clear with quantity call outs, and consolidated #10 pan head screws to all 1-1/4" length for simplicity. Version 2.0 - 8/17/2022 Updated QR Codes, minor formatting, added details for mounting router paddle switch, updated materials list

This stop block is designed to work with a single T-track and allows for a "fenceless" stop block system to be installed in a workshop. The stop block is easily added/removed as needed so as to preserve (and maximize) the work area in a shop. It has also been proven to work in all styles of T-Track (EXCEPT Incra)!All hardware is included depending on the features you choose:The STANDARD stop block comes with:(1) 3D printed stop block in the color of your choice(1) 5/16" T-bolt(1) 5/16" Washer(1) Knob(1) Aluminum wear plate mounted to the frontThe measurement option comes with an additional indicator with reversible mounting on the bottom of the stop block. This custom miter saw stop block is featured in this video: HERE

Need a convenient way to store your DeWalt 20V (and 60V Flexvolt) Batteries around your shop or home? I designed these battery hangers specifically for this purpose. These hangers are 3D Printed in PETG plastic (Black) meaning they will hold up over time. Each hanger provides a snug friction fit to the battery which allows you to mount the hanger in any orientation. They are secured in place with any (4) flat head wood screw but please be aware NOT TO OVER TIGHTEN! Your drill/driver will win in a battle with these plastic hangers. This product is sold in pairs, meaning each pair is comprised of (2) hangers. The price per hanger is reduced the more you buy!

Add a "Shop Greatness" magnet or sticker to your workshop to show the world you are on the path towards it! This slogan has become my Mantra as I build out my workshop on the Shop Nation YouTube channel.The item measures 6" long and 1.5" tall. The thickness of the magnet is 0.020" (0.5mm) and it is flexible so it can be applied to curved surfaces too!This product directly supports Shop Nation and officially makes you a member!